Digital Security Controls PC1616 Instalační manuál Strana 14

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 53
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 13
10
Remote Programming (11 Flashes)
This trouble is indicated during a remote firmware upgrade. Indicates that a remote firmware update is in prog-
ress over GPRS/Ethernet. Trouble will clear automatically when update completes successfully.
Module Configuration Trouble (12 Flashes)
This trouble is indicated when the System Account Code or the Receiver Account have not been programmed.
Disabled receivers are excluded.
Red Network Connection Status LED
BLINKING: Indicates communications in progress.
Once quickly for outgoing Ethernet transmission.
Twice quickly to indicate incoming Ethernet ACK/NACK.
Slowly for incoming or outgoing voice call.
OFF: This is the normal state of the Red Network Connection Status LED. There are no network connection
issues present.
ON: There is a problem with the Ethernet or the GPRS network connection. LED will be ON if any of the follow-
ing occur:
Ethernet cable is not connected,
DHCP configuration times out,
Unit fails to get an IP address from the GPRS network, or
GPRS connection has been reset.
(Green LED 1) (Green LED 2) and (Yellow LED) Signal Strength
NOTE: If the yellow LED is flashing, Signal Strength in table below is not valid.
See Table 6 for troubleshooting flashing yellow LED.
NOTE: The Communicator will indicate GSM Trouble (yellow LED = 5 flashes) if the average
CSQ Level
is 5 or less. The Communicator Signal Strength can be viewed in Connect24.
Network Activity LEDs (Red and Green)
Ethernet Activity:The Red LED will blink quickly once for Ethernet Transmit, or twice for Ethernet Receive.
GPRS Activity: The Green LED 2 will blink quickly once for GPRS Transmit, or twice for GPRS Receive.
SMS Activity: The Green LED 1 will blink quickly once for SMS Transmit, or twice for SMS Receive.
.
Factory Defaults Reset
You can reset the programming options for the Communicator to the factory settings by installing the hardware
jumper. Perform the following steps to reset the Communicator:
NOTE: Two pins require a jumper in order to reset the hardware values.
1. Remove panel front cover.
2. Locate the AUDIO/DEFAULT 5 pin connector in the middle of the Communicator board. On the PC1616/1832/1864 pan-
els pins 4 and 5 are on top. (See
Figure 3
). On the PC9155 panel, pins 4 and 5 are on the right. See
Figure 5
).
3. Apply a jumper to short the hardware default pins 4 and 5.
4. Remove all power from the panel and then apply power to the panel. Wait until the two green LEDs on the
Communicator begin flashing rapidly.
5. Remove the jumper from the hardware default pins 4 and 5. (Green LEDs will stop flashing).
NOTE: Your Communicator has now been reset to the factory default values.
Firmware Update
The firmware of the device can be updated over GPRS or Ethernet (Remote or Local updating):
When the firmware update begins, all LEDs are ON.
During the firmware update process, the LEDs will be cycled individually in a chaser pattern.
After a successful update, the unit will automatically restart.
Should the update fail, all 4 LEDs will flash ON, then OFF together at 1 second intervals.
NOTE: If the firmware update fails, restart the unit. In the event of consistent update failures, contact
your dealer.
Table 5: Radio Signal Strength
SIGNAL
STRENGTH
CSQ
LEVEL
YELLOW
LED
GREEN
LED 2
GREEN
LED 1
SIGNAL LEVEL ACTION REQUIRED
No Signal 0 ON OFF OFF -108.8 dBm
Check Antenna connections. Confirm GSM service
is active. Relocate panel or install an external
antenna.
1 Bar 1 - 4 ON OFF Flashing -108 dBm ~-103 dBm Relocate panel or install an external antenna.
2 Bars 5 - 6 OFF OFF Flashing -102 dBm ~ -99 dBm If possible, relocate panel or install external antenna.
3 Bars 7 - 10 OFF OFF ON -98 dBm to -91 dBm Panel location has acceptable GSM signal level.
4 Bars 11-13 OFF Flashing ON -90 dBm to -85 dBm Panel location has acceptable GSM signal level.
5 Bars 14 + OFF ON ON -84 dBm and higher Panel location has acceptable GSM signal level.
COMMUNICATOR RESET / UPDATE
Zobrazit stránku 13
1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 52 53

Komentáře k této Příručce

Žádné komentáře